Courses:

Ship Structural Analysis & Design (13.122) >> Content Detail



Calendar / Schedule



Calendar


DAY #LECTURESREADINGSPROBLEM SETS
I. Shear and Bending
1Lecture 1: Shear and Bending (PDF)
  • Hull Girder Response Analysis: Ship Structural Design, Hughes, Ch. 3 -- Sections 3.1-3.3.
  • Longitudinal Strength - Excerpt from Part 3: Hull Construction and Equipment. In Rules for Building and Classing Steel Vessels 2003, ABS.
Problem Set 1: Shear and Bending
2Lecture 2: Balance (PDF)Problem Set 2: Shear and Bending, Balancing
II. Characteristics of Thin Walled Sections
3Lecture 3: Bending Without Twist (PDF)Problem Set 3: Shear Stress, Center of Twist
4Lecture 4: Pure Twist Open Section (PDF)Problem Set 4: Combined Torsion and Multi-Cell St. Venant's Torsion
5Lecture 5: Pure Twist Closed Section (PDF)
6Lecture 6: Pure and Warping Torsion (PDF)
7
  • Lecture 7: Calculation Of Section Properties - Open (PDF)
  • Lecture 7a: Calculation of Section Properties Closed (PDF)
8
  • Lecture 8: Shear Center - Closed Section (PDF)
  • Lecture 8a: Shear Stress Multicell Section (PDF)
  • Lecture 8b: St. Venant Torsion Multi-cell (PDF)
9
  • Lecture 9a: Composite Sections (PDF)
  • Lecture 9b: Shear Lag (PDF)
  • Lecture 9c: Yield Criteria (PDF)
  • Ch. 3 and 6 of Hughes.
  • Refererence: Ch. 11 of Shames.
III. Introduction to MaestroProblem Set 5: Maestro Tutorial and building model (preliminary)
IV. Design Approach and Failure Analysis
10Design Philosophy and Approach (PDF)Structural Design Introduction: Ch. 1 and 2 of Hughes.
11Loads and Design
Approach continued (PDF)
V. Plate Bending
12Plate Bending Introduction (PDF)
13Plate Bending (PDF)
14Plate Bending Solution (PDF)
VI. Panel, Girder, Frame Bending Failure Analysis
15Panel, Girder and Frame Limit States (PDF)Plastic Hinge and Plastic Section Analysis: Section 16.1 of text.Problem Set 6: Panel and Girder PSF Calculations
VII. Buckling and Ultimate Strength of Columns
16Buckling (PDF)Buckling and Ultimate Strength of Columns: Ch. 13 of text.
  • Problem Set 7: Design Notes Part II
  • Problem Set 8: Design Notes Part III
VIII. Buckling and Ultimate Strength of Plates
17Plate Buckling (PDF)Buckling and Ultimate Strength of Plates: Ch. 12 of text.
IX. Buckling of Stiffened Panels
18Buckling of Stiffened Panels (PDF)Longitudinally Stiffened Panels: Section 13.1 of text. Includes local buckling of stiffener (tripping).
X. Ultimate Strength of Stiffened Panels
19Ultimate Strength of Stiffened Panels (PDF)Ultimate Strength of Stiffened Panels: Ch. 14 of text.
XI. Matrix, Grillage and FEM Analysis
20Intro to Matrix Analysis (PDF)
  • Example of Grillage Analysis.
  • Constant Stress/Strain Triangle Element: Hughes 7.3.
21Matrix Analysis continued (PDF)
22Pin-jointed Beam Example (PDF)
23Flexure Only Beam - General Method (PDF)
24Grillage Introduction
Degrees of Freedom (PDF)
Final ProjectBarge Optimization


 

 

 

 

 








© 2010-2021 OpenCollege.com, All Rights Reserved.
Open College is a service mark of AmeriCareers LLC.